gassero GSR-20-HC Page 35 Installation And User Manual Download

Page: 35 / 38

13.4.3

UNIT STATUS CHECKING

1# means System 1, 2# means Syestem2

13.4.4

THE MANOMETER INSTUCTION

The manometer is a kind of high pressure equipment, when the heat pump is on, the manometer pointer would point to the

pressure value of refrigerant, the max. value of protection is 42kg/Cm2. When the heat pump is off, the pointer would point

to the same value as actual ambient temperature (e.g. 28

°C) and related air pressure (e.g.18kg/ Cm2).

Please check the manometer when you restart the heat pump after not using for a long time, if it shows

ambient temperature valve is smaller than 2

°C

（

When the ambient temp. is higher than 2°C

）

, it means that refrigerant

has leaked a lot, and you need to confirm with professional engineer as soon as possible.

Code

Description

1# Coil temperature

1# Compressor suction temperature

1# Compressor discharge temperature

Ambient temperature

DHW outlet temperature

Heating/Cooling outlet water temperature

Reserved

1# Compressor current

1# Open steps of EEV

A10

Reserved

2# Coil temperature (double-system unit only)

2# Compressor suction temperature (double-system unit only)

2# Compressor discharge temperature (double-system unit only)

2# Compressor current (double-system unit only)

2# Open steps of EEV (double-system unit only)

History record of error code

ON or Off state

Status interface

Select parameter

℃

Return to

homepage

℃

Summary of Contents for GSR-20-HC







































Search results

Summary of Contents for GSR-20-HC

Reviews:

Related manuals for GSR-20-HC

Brands by name

Popular brands

gassero GSR-20-HC, Installation And User Manual

Search results

Summary of Contents for GSR-20-HC

Reviews:

Related manuals for GSR-20-HC

Brands by name

Popular brands