Home
/
GAS GAS
/
TXT 2018 Series
/
Workshop Manual

GAS GAS TXT 2018 Series, Workshop Manual

Share

Page: 60 / 84

background image

Workshop manual

-60-

maintenance of the frame

- Remove the cartridge from the tube.

- Turn the fork and remove the hydraulic end of stroke cone.

- Push the compression unit inwards and remove the seeger from its housing.

- Remove the compression assembly.
- Place the cartridge in an oil collection device and have the rod inserted in the

cartridge tube for complete drainage of the oil.

- Reinsert the hydraulic unit into the cartridge.
- Reinsert the seeger into its housing (see figure), making sure it is correctly

positioned.

«
...
58
59
60
61
62
...
»

Summary of Contents for TXT 2018 Series





















































































Reviews:

No comments

Related manuals for TXT 2018 Series

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: Yamaha Pages: 124

Brand: Ohlins Pages: 8

Brand: VEB Pages: 63

Brand: yasuni Pages: 12

Brand: Termignoni Pages: 9

Brand: Parweld Pages: 37

Brand: hepco & becker Pages: 2

Brand: BMW Motorrad Pages: 231

KAWASAKI ZX6R 2007/8

Brand: Evotech Performance Pages: 2

Brand: TVS Pages: 48

Brand: Honda Pages: 123

Brand: DYNATEK Pages: 11

Brand: DYNATEK Pages: 12

Brand: hepco & becker Pages: 2

Brand: SW-Motech Pages: 2

HPS.11.258.900-01

Brand: SW-Motech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands