Garmin GPSMAP 198C Owner'S Manual Download Page 67

Page: 67 / 126

GPSMAP 198C Sounder Owner’s Manual

AIN

ENU

DSC T

You can use the Review On Map option to show a saved track on a

Track Map Page.

To start a TracBack from the Saved tab list:

1. Using the

ROCKER

, highlight a track, and press

NAV

2. The

Follow <track name>

automatically appears

highlighted. Press

ENTER

3. Choose either

Original

, which navigates you from the end

to the start of your trip, or

Reverse

, which navigates you

from the start to the end of your trip, and press

ENTER

The track name

automatically

appears when

highlighted on the

Saved list and

NAV

is pressed.

DSC Tab

Digital Selective Calling (DSC) uses marine VHF radio and Global

Positioning System (GPS) technologies to transmit and receive

location information. DSC is used by mariners to assist them in two

major areas: Distress Calls and Position Reporting. See

page 22

and the “Appendix” for more information on DSC and using it with

your GPSMAP 198C Sounder.

Summary of Contents for GPSMAP 198C































































































































Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands

Garmin GPSMAP 198C, Owner'S Manual

Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands