Garmin GPSMAP 198C Owner'S Manual Download Page 49

Page: 49 / 126

GPSMAP 198C Sounder Owner’s Manual

AIN

ENU

IDE

GPS Tab Options

The GPS tab features an options page that provides access to

functions and features relating to the GPS Info Page.

To show and select the GPS Tab options:

1. Press

MENU

2. Using the

ROCKER

, highlight an option, and press

ENTER

NOTE:

If a DGPS receiver is attached to the unit and Garmin

DGPS, RTCM In/NMEA Out, or Other DGPS is enabled on

Port 2, WAAS is automatically disabled (WAAS Off). It is not

possible for the GPSMAP 198C Sounder to receive WAAS and

DGPS corrections at the same time.

GPS Tab Options

Tide Tab

The Tide tab shows a graphical chart that shows tide station

information in a 24 hour span starting at midnight station time. You

can choose from different dates and more than 3,000 tide stations.

Tide Tab

Station

Name

Date

Tide

Chart

Event

Times

The top of the page shows the tide station being referenced, below

that the date. The top of the chart shows a 24-hour block of local

time (LCL) for your location, with the reported station time (STA)

appearing at the bottom. Daytime (light bar) and nighttime (dark

bar) show across the time scale, with the time progressing from

left to right. (Local time scales and sunrise/sunset info can not

be available for a few stations). The solid, light vertical lines are

Summary of Contents for GPSMAP 198C































































































































Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands

Garmin GPSMAP 198C, Owner'S Manual

Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands