Garmin GPSMAP 198C Owner'S Manual Download Page 37

Page: 37 / 126

GPSMAP 198C Sounder Owner’s Manual

AIN

AGES

AGE

Map Page Options

Full Screen Map/Show Data

—toggles between the Map Page

without or with data ﬁelds on the Map Page.

To maximize the map/show data ﬁelds:

1. Highlight

Full Screen Map

, and press

ENTER

. The Map

Page is now maximized with no data ﬁelds.

2. To show the data ﬁelds again, press

MENU

, highlight

Show

Data

, and press

ENTER

Change Numbers

—speciﬁes the type of data shown in each data

ﬁeld used on the Map Page.

To change a data ﬁeld:

1. From the menu, use the

ROCKER

to highlight the

Change

Numbers

option, and press

ENTER

2. Move the ﬁeld highlight to the data ﬁeld you want to change,

and press

ENTER

3. Move up or down on the list using the

ROCKER

to highlight

the data you want to show, and press

ENTER

. To exit, press

QUIT

NOTE:

Pointer, Highway, Location, and Sonar ﬁeld options

are only available on medium and large sized data ﬁelds.

Summary of Contents for GPSMAP 198C































































































































Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands

Garmin GPSMAP 198C, Owner'S Manual

Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands