Garmin GPSMAP 198C Owner'S Manual Download Page 10

Page: 10 / 126

GPSMAP 198C Sounder Owner’s Manual

ASIC

PERATION

DJUSTING

THE

ACK

IGHT

The Set Position,

Track Control, Track

and Speed ﬁelds

only show while in

Simulator Mode.

To enter a simulated speed and heading from the

Main Menu:

1. Press

MENU

twice to show the

Main Menu

2. Use the

ROCKER

to highlight the

Systm

tab, press

right then down until the ﬁeld below the word

Speed

highlighted, then press

ENTER

3. Use the

ROCKER

to enter a speed, and press

ENTER

4. Use the

ROCKER

to highlight

Track Control

. Press

ENTER

, and select a heading.

5. Press

ENTER

to ﬁnish, and

QUIT

until you return to the

Map Page.

To adjust the simulated speed and heading from the

Compass or Highway Pages:

1. Press up on the

ROCKER

increase the speed in

10 knot/kph/mph increments. Press down on the

ROCKER

to decrease the speed in the same increments.

2. Press left and right on the

ROCKER

to steer the boat.

Adjusting the Backlight

The Sounder’s adjustable screen backlighting is controlled with the

POWER

key, and can be adjusted from any page.

To adjust the backlighting:

1. Press and release the

POWER

key. The adjustment slider

window appears.

2. Press the

POWER

key again and the user-deﬁned level of

backlighting starts. You can adjust this level by pressing up

or down on the

ROCKER

. If you press

POWER

one more

time, the backlight is at the maximum setting.

3. Press

ENTER

QUIT

when ﬁnished.

Summary of Contents for GPSMAP 198C































































































































Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands

Garmin GPSMAP 198C, Owner'S Manual

Search results

Summary of Contents for GPSMAP 198C

Reviews:

Related manuals for GPSMAP 198C

Brands by name

Popular brands