manualshive.com logo in svg

Garmin GNC 255A, Pilot'S Manual

Share
Download
Garmin GNC 255A Pilot'S Manual Download Page 38

3-16

Garmin GNC 255A/255B Pilot’s Guide

190-01182-01 Rev. E

Functions

3.5   System Configuration

The System Configuration function displays the software version, database 
information, and serial number.  This information is helpful when contacting 
customer support. It also allows setting the COM spacing, display brightness and 
contrast, and to update databases. 

3.5.1 COM Spacing

COM spacing may be selected between 8.33 kHz and 25 kHz to allow for regional 
requirements. 

NOTE

When switching from 8.33 kHz to 25 kHz mode, any 8.33 kHz-specific user 
frequencies will be deleted from the user frequency list. This only affects the user 
frequencies within the 8.33 kHz spectrum. 

 COM Spacing

1.

Press 

FUNC

.  

2.

Turn the outer knob to SYS CONFIGURATION. 

3.

Turn the inner knob to COM SPACING. 

4.

Press 

ENT

.

5.

Turn the inner knob to set the COM spacing.

6.

Press 

ENT

 to save the selected value.

Press 

CLR

 to cancel the change.

Channel Spacing

Summary of Contents for GNC 255A























































Reviews:

No comments

Brands by name

Popular brands

Load more brands