background image

GHP 10 Installation Instructions 

19

Device

Specification Measurement

CCU

Dimensions

19

/

32

 in. diameter (91.4 mm)

Weight

5.6 oz. (159 g)

Temperature 

range

From 5°F to 140°F (from -15°C to 55°C)

Case material Fully gasketed, high-impact aluminum 

alloy, waterproof to IEC 529 IPX7 

standards

CCU/ECU 

interconnect 

cable length

16 ft. (5 m)

NMEA 2000 

LEN

2 (100 mA)

Alarm

Dimensions

(L × Diameter) 

29

/

32

 × 1 in. (23 × 25 mm)

Weight

2.4 oz. (68 g)

Temperature 

range

From 5°F to 140°F (from -15°C to 55°C)

Cable length

10 ft. (3.0 m)

GHC 10

Dimensions

5

/

16

 × 4 

3

/

8

 × 1 

29

/

32

 in. (109 × 111 × 48 

mm)

Weight

9.6 oz. (272 g)

Cables

NMEA 0183 data cable – 6 ft. (1.8 m)
NMEA 2000 drop cable and power cable – 

1

/

2

 ft. (2 m)

Temperature 

range

From 5°F to 158°F (from -15°C to 70°C)

Compass-safe 

distance

1

/

2

 in. (241 mm)

Case material Fully gasketed, high-impact aluminum 

alloy, waterproof to IEC 529 IPX7 

standards

GHC 10 power 

usage

2.5 W max.

NMEA 2000 

input voltage

9–16 Vdc

NMEA 2000 

LEN

6 (300 mA)

nMEa 2000 PGn Information

CCu

type

PGn

Description

Receive

059392

ISO Acknowledgment 

059904

ISO Request 

060928

ISO Address Claim 

126208

NMEA - Command/Request/Acknowledge 

Group Function

126464

Transmit/Receive PGN List Group Function

126996

Product Information

127258

Magnetic Variation

127488

Engine Parameters - Rapid Update

129025

Position - Rapid Update

129026

COG & SOG - Rapid Update

129283

Cross Track Error

129284

Navigation Data

Transmit

059392

ISO Acknowledgment

059904

ISO Request

060928

ISO Address Claim

126208

NMEA - Command/Request/Acknowledge 

Group Function

126464

Transmit/Receive PGN List Group Function

126996

Product Information

127250

Vessel Heading

GHC 10

type

PGn

Description

Receive

059392

ISO Acknowledgment 

059904

ISO Request 

060928

ISO Address Claim 

126208

NMEA - Command/Request/Acknowledge 

Group Function

126464

Transmit/Receive PGN List Group Function

126996

Product Information

127245

Rudder Data

127250

Vessel Heading

127488

Engine Parameters - Rapid Update

128259

Water Speed

129025

Position - Rapid Update

129029

GNSS Position Data

129283

Cross-Track Error

129284

Navigation Data

129285

Navigation - Route/WP information

130306

Wind Data

130576

Small Craft Status

Transmit

059392

ISO Acknowledgment

059904

ISO Request

060928

ISO Address Claim

126208

NMEA - Command/Request/Acknowledge 

Group Function

126464

Transmit/Receive PGN List Group Function

126996

Product Information

128259

Water Speed

129025

Position - Rapid Update

129026

COG & SOG - Rapid Update

129283

Cross Track Error

129284

Navigation Data

129540

GNSS Sats in View

130306

Wind Data

The GHP 10 and the GHC 10 are NMEA 2000 certified.

Summary of Contents for GHP 10 Marine Autopilot System



























Reviews: