Garmin GDL 82 Installation Manual Download Page 47

Page: 47 / 68

System Configuration

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 7-1

System Configuration

7.1

GDL 8X Install Tool ........................................................................................................................................ 7-2

7.2 Diagnostics .................................................................................................................................................... 7-4

7.2.1 GDL 82 Unit Information Page................................................................................................................. 7-4
7.2.2 Discretes

Page ......................................................................................................................................... 7-5

7.2.3 GPS

Page ................................................................................................................................................ 7-6

7.2.4 GPS Sat Status Page ................................................................................................................................ 7-7
7.2.5 ADS-B

Page............................................................................................................................................. 7-8

7.2.6 Faults

Page.............................................................................................................................................. 7-9

7.2.7 Assert Log Page....................................................................................................................................... 7-9

7.3 Configuration .............................................................................................................................................. 7-10

Selections ................................................................................................................................... 7-12

7.4

Software Loading Instructions...................................................................................................................... 7-13

This section provides configuration instructions that include:

•

Basic diagnostics information

•

Load software into the GDL 82 (if required)

•

Configure the GDL 82 for the specific installation

Summary of Contents for GDL 82





































































Search results

Summary of Contents for GDL 82

Reviews:

Related manuals for GDL 82

Brands by name

Popular brands

Garmin GDL 82, Installation Manual

Search results

Summary of Contents for GDL 82

Reviews:

Related manuals for GDL 82

Brands by name

Popular brands