background image

4  

GDL 40 Installation Instructions

Mounting the Antenna with the Cable 

Routed through the Pole

1.  Select a mounting location for the 

antenna, and verify correct operation at 

the mounting location (

page 2

).

2.  Temporarily position a standard marine 

pole mount (not included) in the 

mounting location you selected (

page 2

).

3.  Mark the approximate center of the pole.
4.  At the marked location, use a 

3

/

4

 in. 

(19 mm) bit to drill a hole for the cable 

to pass through.

5.  Fasten the marine pole mount to the boat 

(hardware not included).

6.  Thread the pole-mount bracket 

 onto 

the marine pole mount.

  Do not overtighten the bracket.

➋ 

➌ 

7.  Route a NMEA 2000 drop cable through 

the pole-mount bracket and the pole, and 

connect the cable to the antenna.

8.  Place the antenna on the pole-mount 

bracket, and twist it 

 to lock it in 

place. 

9.  Secure the antenna to the bracket with 

the included M3 set screw 

.

10. Route the NMEA 2000 drop cable away 

from sources of electronic interference.

11. Connect the antenna to your NMEA 

2000 network (

page 5

).

12. After the antenna is installed on the pole 

mount, fill the vertical cable slot with a 

marine sealant (optional). 

Mounting the Antenna under a 

Surface

NOTICE

When choosing a location to install the 

under-deck-mounting bracket, make sure 

the included screws are not too long for 

the surface thickness. If the screws are not 

appropriate for the surface, you must supply 

the correct length of M4 screws to avoid 

damage to the top of the mounting surface.
The antenna can be mounted under a 

fiberglass surface. Because the antenna has 

difficulty acquiring cellular signals through 

metal, it is recommended that you use the 

under-deck mount under a fiberglass surface.
1.  Identify the mounting location on the 

fiberglass surface 

, and verify correct 

operation at the mounting location 

(

page 2

).

➌ 

2.  Using the under-deck-mounting bracket 

 as a template, mark three pilot-hole 

locations 

 

on the surface.

3.  Use a 

1

/

8

 in. (3.2 mm) bit to drill the 

three marked pilot holes.

4.  Place the antenna in the bracket, and 

twist it clockwise to lock it in place. 

5.  Secure the antenna to the bracket with 

the included M3 set screw 

.

6.  Remove the backing from the adhesive 

pads 

 on the under-deck mounting 

bracket.

7.  Make sure that the bracket aligns with 

the pilot holes, and adhere the under-

deck mounting bracket to the surface.

8.  Using screws of the appropriate length, 

fasten the bracket to the surface.

9.  Connect a NMEA 2000 drop cable to the 

antenna 

.

10. If you are using an external cellular 

antenna (

page 5

), connect it to the 

GDL 40 antenna 

.

Summary of Contents for GDL 40











Reviews: