background image

Elliott Aviation Technical Products Development, Inc. 

Report No.: ICA-3832-560 

6601 74

th

 Ave Building A

Revision: IR 

Milan, IL 61264 

Dated 01/23/2018 

8 of 21 

Instructions for Continued Airworthiness For Garmin ADS-B System Installation 

2.3.2  GTX 3000 Transponder (Removal & Installation Only)

 

2.3.2.1 

Confirm Garmin GTX 3000 line replaceable unit part number from the Elliott Aviation wiring 

diagram 237-3832-E0560-000 located in Appendix A. 

2.3.2.2 

Obtain Elliott Configuration Instructions located in Appendix A.  Read sections 2 and 4 of this 

document before proceeding with reconfiguring of the GTX 3000. Take special note of the 

requirements for laptop computer interface and software effectivity details.  

The GTX 3000 will not function properly until software setup and configuration is accomplished.

 

PRECAUTION: 

Part number, configuration and electrical interface has been evaluated 

and approved for ADS-B Latency and SDA requirements. Any deviations 

will require additional approval. 

2.3.2.3 

While using the Elliott Configuration Instructions, access to the GTX 3000 status is available. Real 

time information is presented. 

2.3.2.4 

For setup and configuration, the following items must be verified: 

GPS Position

Magnetic

Weight on wheels is operating correctly.

ADS-B mode indicated.

4096 code agrees with RMU ATC settings.

Flight ID agrees with RMU ATC settings.(note: Dynamic (pilot set) Flight ID not available

on aircraft all.)

TCAS status correct for aircraft. Most aircraft will have TCAS installed.

2.3.2.5 

GPS position is confirmed using the “Info / ADS-B Out” page.  Confirm GPS position from the GDL 

88. Sample page follows to show typical GTX 3000 GPS source information.

2.3.2.6 

Heading is confirmed using “Info / EHS” page.  Confirm heading from the Pro Line 4 system.  

Sample page follows to show typical GTX 3000 Heading source information. 

2.3.2.7 

WOW, ADS-B mode, 4096 Code, Flight ID, and TCAS status is confirmed using the “Status” page 

in the GTX 3000 configuration tool.  Sample page follows to show typical GTX 3000 “Status” page 

information. 

2.3.2.8 

After these have been verified perform 14 CFR 43 App F ¶ A-J. 

2.3.2.9 

The aircraft may now be returned to service. 

Summary of Contents for ADS-B























Reviews: