Garmin 3000 Series Installation Instructions Manual Download Page 9

9

GPSMAP 3000 Series Installation Instructions

Garmin Marine Network

The Garmin Marine Network is a waterproof ethernet-based system that allows Garmin chartplotters to communicate with Garmin sensors 

and other Garmin chartplotters over the network. Waterproof RJ-45 connections allow for simple installation and high-speed connectivity. For 

a simple installation with one Garmin chartplotter and one Garmin sensor, the two devices can be directly connected with a Garmin Marine 

Network cable. 

 

NotE: 

Power connections for network components are not shown in the following illustrations. All components of the Garmin Marine Network must 

be connected to power, because they do not receive power through the network connections.

Garmin  

GPSMAP 3000 

Series Chartplotter

GPS 17x

Garmin  

GPSMAP 

3000 Series 

Chartplotter

Simple Garmin Marine Network With Two Chartplotters

If more than two GPSMAP 3000 series chartplotter are installed, use a Garmin Marine Network Port Expander (GMS 10) to expand the 

network. If two or more GPSMAP 3000 series chartplotters are installed and networked, only one GPS 17x antenna needs to be installed. You 

can add up to five total devices to the Network Port Expander. If more than five are needed, you can add more Network Port Expanders to the 

network. This network is NOT compatible with PC networks. 

Do Not attach PC devices to the Garmin Marine Network. 

Some examples 

of the Garmin Marine Network are included below. Refer to the individual installation instructions for the individual sensors. Additional 

Garmin network cables are available from your Garmin dealer or direct from Garmin.
You can also include GPSMAP 4000/5000 series chartplotters in your Garmin Marine Network. Refer to the GPSMAP 4000/5000 Series 

Installation Instructions for more information.

xx

xxxxxxxxxxxxxxxxxxxxxxxxx

Garmin GMS 10 

Marine Network Port Expander

Garmin GMR 18 

Marine Radar

Garmin GDl 30A 

Marine Weather/Audio 

Satellite Recieiver

Garmin  

GPSMAP 3000 

Series Chartplotter

Garmin  

GPSMAP 

3000 Series 

Chartplotter

GPS 17x

Garmin GSD 21 

Sounder Module

To transducer

Expanded Garmin Marine Network With a GMS 10 and Additional Devices

Serial cable

Ethernet cable

Transducer cable

xxxxxxxxx

Serial cable

Ethernet cable

Transducer cable

xxxxxxxxx

Summary of Contents for 3000 Series











Reviews: