Garmin 3000 Series Installation Instructions Manual Download Page 10

Final Wiring Connection

After all the wiring is complete, the cables are attached on the backside of the GPSMAP 3000 series chartplotter. If the chartplotter is not 

connected to a Garmin Marine Network, be sure to firmly affix the weather cap over the open connector to limit corrosion of the contacts. The 

connection ports are labeled on the back of the chartplotter.

To install the Power/NMEA, Marine Video, and Network Cables:

1.  Align the notch and locking ring tab on the black Power/NMEA cable with the black 

POWER/NMEA

 port on the back of the unit. Carefully 

press the cable in until it is firmly seated. 

Do not force the cable, because this may damage the pins.

2.  After the cable is seated, turn the locking ring clockwise until it stops.
3.  Repeat S*teps 1 and 2, attaching the gray Marine Video cable to the gray 

VIDEO

 port on the back of the unit.

4.  If you are connecting the GPSMAP 3000 series chartplotter to a Garmin Marine Network, insert the RJ-45 connector into the 

NETWORK

 

port on the back of the unit and screw the locking ring in clockwise until it is firmly seated.

With power applied to the circuit, test the installation by pressing the 

PoWER

 key on the front of the unit. Refer to your GPSMAP 3000 series 

Owner’s Manual for steps on initializing and using the chartplotter.

Updating the Chartplotter Software

Your GPSMAP 3000 series chartplotter may contain a software update Data card. If so, follow the instructions provided with the card.
If a software update Data card is not included, visit 

www.garmin.com

 to make sure your chartplotter software is up-to-date. If your software is 

not up to date, follow the directions on 

www.garmin.com

, or contact 

www.garmin.com/support

.

To determine the version of software on your chartplotter:

1.  Hold 

ADJ/Menu

 to open the Main Menu.

2.  Select 

System 

Update 

to view the installed software version.

For the latest free software updates (excluding map data) throughout the life of your  

Garmin products, visit the Garmin Web site at www.garmin.com.

© 2008 Garmin Ltd. or its subsidiaries

Garmin International, Inc. 

1200 East 151

st

 Street, Olathe, Kansas 66062, USA

Garmin (Europe) Ltd. 

Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9RB UK

Garmin Corporation 

No. 68, Jangshu 2

nd

 Road, Shijr, Taipei County, Taiwan

www.garmin.com

Part Number 190-00991-02 Rev. A

Summary of Contents for 3000 Series











Reviews: