Gardner Denver Welch LVS 105 T 10 ef+ Operation Manual Download Page 60

Page: 60 / 64

Spare parts overview

Operation Manual LVS 105 T

– 10 ef

Spare parts overview

The spare parts list includes all spare parts with the required order information.

When placing your order, specify the name, quantity, serial number and order number!

LIABILITY

►

We are not liable for damage due to the installation of other parts than
those provided by the manufacturer, Gardner Denver Thomas GmbH.

9.1 Diaphragm pump service set

Designation

Order numbers

Complete service set

402044

O-rings, valves, diaphragms, see section

8.2.2 Re-

placing the components in the pump

unit

Emission condenser

700183-11

Separator

Spherical joint clip, stainless steel, for KS 35

828857-35

Round-bottom flask 500 ml KS 35

828845

Attachments

PTFE tube 8 x 1 mm

828331

Hose nozzle PP, DN8-

G1/4“

710798-06

Straight fitting PVDF 8-

1/8“

829919

Angle fitting

829936-1

O-ring EPDM, Ø 8 x 2

829210-3

9.2 Ordering and service contact

Manufacturer:

Gardner Denver Thomas GmbH

Am Vogelherd 20

98693 Ilmenau

Germany

Tel.:

+49 3677 604 0

Fax:

+49 3677 604 131

E-mail:

[email protected]

Web:

www.gardnerdenver.com/de-de/welch

Customer support +49 3677 604 0

Summary of Contents for Welch LVS 105 T 10 ef+

































































Search results

Summary of Contents for Welch LVS 105 T 10 ef+

Reviews:

Gardner Denver Welch LVS 105 T 10 ef+, Operation Manual, Page: 60 / 64

Search results

Summary of Contents for Welch LVS 105 T 10 ef+

Reviews: