background image

2 Introduction

2.1 Introduction

Serial number:

PIN code:

Product registration key:

The serial number is on the product carton and on the product rating plate. Refer to 

Product overview on page 7

.

Use the serial number to register your product on www.gardena.com.

2.1.1 Support

For support about the GARDENA product, speak to your

GARDENA service.

2.1.2 Product description

Note: 

GARDENA regularly updates the appearance

and function of the products. Refer to 

Support on page

6

.

The product is a robotic lawn mower. The product has a

battery power source and cuts the grass automatically. It

continuously alternates between mowing and charging.

The movement pattern is random, which means that the

lawn is mowed evenly and with less wear. The boundary

wire and the guide wire controls the movement of the

product within the work area. Sensors in the product

senses when it is approaching the boundary wire. The

front of the product always passes the boundary wire

by a specific distance before the product turns around.

When the product hits an obstacle or approaches the

boundary wire the product selects a new direction.

You can select the operation settings in the GARDENA

Bluetooth

®

 App or with the buttons on the keypad of the

product. The app and the LED status indicator show the

operation mode of the product.

2.1.2.1 Mowing technique
The frequent cutting technique improves the grass

quality and decreases the use of fertilizers. Collection

of grass is not necessary.

2.1.2.2 Find the charging station
The product operates until the battery state of charge

is low, then the product starts to go to the charging

station. The guide wire is put from the charging station

to a remote part of the work area or through a narrow

passage. The guide wire is connected with the boundary

wire to make it easier and faster for the product to find

the charging station.

2.1.2.3 GARDENA Bluetooth

®

 App

The product can be operated with the keypad on the

product and use the factory settings of the product.
To adjust the settings of the product the GARDENA

Bluetooth

®

 App is used. The product can be controlled

remotely with Bluetooth

®

 within short range.

6 - Introduction

1585 - 007 - 26.10.2022

Summary of Contents for SILENO minimo













































Reviews: