manualshive.com logo in svg

Gap Diagnostic IIDTool Pro G3, User Manual

Share
Download
Gap Diagnostic IIDTool Pro G3 User Manual Download Page 43

42

43

IIDT

ool

GAP Diagnostic 2023-09-12 All Rights Reserved 

User Manual G3 units : Version 37, Firmware V4.0

Figure  18. 

Updater software overview

2.5.2 Update ECU files only

When new ECU files use by the ECU Flash function are available, you can download them to the IID

-

Tool without updating the IIDTool firmware itself. This speeds up the process.

1-  Connect the tool to the USB port of the computer using the USB cable

2-  Start the updater software previously installed in the computer

3-  Click on “ FIND DEVICE ” and wait for pairing of the tool with the updater software. Once paired, 

the user information, vehicle information and current firmware version of the tool will be dis

-

played.

4-  Click on “ PROGRAM FLASH FILES ONLY ”. The evolution of each data file is observable in 

succession on the progress bar.

Figure  19. 

Overview, “ Program Flash File Only ” button

Summary of Contents for IIDTool Pro G3





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands