manualshive.com logo in svg

Gap Diagnostic IIDTool Pro G3, User Manual

Share
Download
Gap Diagnostic IIDTool Pro G3 User Manual Download Page 186

186

IIDT

ool

GAP Diagnostic 2023-09-12 All Rights Reserved 

User Manual G3 units: Version 37, Firmware V4.0

4.14.2 Voltage displayed

When this feature is enabled, the IIDTool is connected and the user has not called up the IIDTool menu, 

the battery voltage will be displayed. 

4.14.3 Enter unlock code/Pre-Unlock

You can unlock the advanced programming functions on your IIDTool for future uses on other vehicles 

by entering an unlock code here. First, enter the unlock code menu, you will see a ten hexadecimal 

character activation code.

If you don’t have an unlock code or need a new one for adding one or more vehicles, please contact 

us or visit our website to buy additional VIN’s license(s). With your activation code and VIN licence(s), 

you will be able to retrieve your unlock code on our website (

section 2.9

).

After entering your unlock code, when connecting to another vehicle that’s never been unlocked, you 

will be asked if you want your IIDTool to be unlocked for this particular vehicle.

Summary of Contents for IIDTool Pro G3





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands