manualshive.com logo in svg

Gap Diagnostic IIDTool Pro G3, User Manual

Share
Download
Gap Diagnostic IIDTool Pro G3 User Manual Download Page 171

170

171

IIDT

ool

GAP Diagnostic 2023-09-12 All Rights Reserved 

User Manual G3 units : Version 37, Firmware V4.0

RLM Air Suspension 

(L322-06, L322-10, L319, L320)

User can choose between the Hitachi and AMK (introduced in 2012 as the new replacement part) com

-

pressor firmware. The firmware for vehicles fitted with the Hitachi compressor contains modifications 

on the compressor logic and temperature thresholds to increase its longevity. Re-flashing the suspen

-

sion ECU takes around one minute.

Identify firmware: 

This function will return which firmware is currently in the Suspension ECU (Hitachi 

or AMK).

Risk Level

Consequences

Recovery Method

Precautions

Moderate

Suspension system non functioning. 

The vehicle should only be driven for 

a short distance

Repeat reflashing 

procedure

None

Table  34. 

Risk, updating the suspension ECU

On L319-04 vehicles fitted with an earlier RLM firmware version, the suspension warning lamp 

may turn ON after the IPC firmware is updated. Proceed with updating the RLM Suspension 

ECU to fix this issue.

 

Summary of Contents for IIDTool Pro G3





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands