Gap Diagnostic IIDTool Pro G3 User Manual Download Page 167

Page: 167 / 188

166

167

IIDT

ool

User Manual G3 units : Version 37, Firmware V4.0

4.11.4

Available Re-Flash

Engine Remaps, EGR blanking and the likes.

All IIDTools are now capable of transporting products designed and sold by the good people of BAS

Remaps (Bell Auto Services). For more details, please visit their website at:

http://bellautoservices.co.uk/

or send them an e-mail at

[email protected]

Table 32.

Risk, Engine Remaps, EGR blanking and the likes

Prerequisites

• Have access to a Mac or PC computer connected to the Internet

• Having installed the updater software (

section 2.3

)

• Ensure that the updater software installed is at version 4.6 (PC), 4.1 (Mac) or higher.

•

Pro

Ensure the firmware of IIDTool is at least the compiled version in 2454.

Else, simply pro

ceed with updating the IIDTool

Pro

See

section 2.5.

Step 1: Providing BAS with the required information

In order to build a personalised file, BAS Remaps will need to know the current ECU information and

vehicle identification number (VIN). After initial contact with BAS, retrieve the ECU information (IIDTool

Menu-

ECU Info-

Engine) and send them to BAS Remaps at

[email protected]

. Make sure your

vehicle identification number (VIN) is visible in the email header or subject line (

Pro

not hidden or

obfuscated).

Risk Level

Consequences

Recovery Method

Precautions

Moderate Engine will not start

Repeat reflashing

procedure

None

Summary of Contents for IIDTool Pro G3


























































































































































































Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands

Gap Diagnostic IIDTool Pro G3, User Manual

Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands