Gap Diagnostic IIDTool Pro G3 User Manual Download Page 137

Page: 137 / 188

136

137

IIDT

ool

User Manual G3 units : Version 37, Firmware V4.0

4.8.2 Viewing live values

Live value selection and sampling rate

You can select up to 8 live values in the graph and numeric display modes. All 8 values can be viewed

simultaneously. The maximum sampling rate of each live value is divided by the number of live values

selected. For example, if one live value is selected, the maximum sampling rate will be 16 per second

/ 1 live values = 16 samples per second. If four values are selected, 16/4 = 4 samples per second for

each live values. The absolute maximum sampling rate of each live value is determined by the ECU.

All except L322 2002 to 2004.

User can choose between tested and untested live values. Untested

live values will not work (N/A) on every vehicle and configurations. They may also be dependent on the

firmware version of the ECU.

Basic controls

Press in the yellow area to make the top option bar appear.

Figure 61.

LV :

Calling the top bar

Figure 62.

LV : Top bar options

Full screen / split screen button

This button begins recording data. Once pres-

sed, the stop button (same location) will allow the

user to stop, save and name the recording (log) if

required. Saved logs can be accessed by selec

ting “Logs” in the Live Values or login screen (off-

line mode allowed). See

section 4.8.4

Summary of Contents for IIDTool Pro G3


























































































































































































Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands

Gap Diagnostic IIDTool Pro G3, User Manual

Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands