Gap Diagnostic IIDTool Pro G3 User Manual Download Page 115

Page: 115 / 188

114

115

IIDT

ool

User Manual G3 units : Version 37, Firmware V4.0

• The Diesel Particulate Filter is replaced

• The differential pressure sensor is replaced

• The Engine ECU is replaced

DPF Diesel Particulate Filter Replacement (L316-12, L405 4.4L, L494 4.4L, L319 3.0L

L320 3.0L, 2017+)

Usage

This routine is required when the Diesel Particulate Filter is replaced.

This routine should only be used after the Diesel Particulate Filter is replaced.

DPF Dynamic Regeneration (VIN Locked, L319, L320, L322-06, L322-10, L405, L462, L494,

L538, L550, L551, L560, L663, X540, X761, X590, X760, X260)

Usage

This routine is used when a forced regeneration is required (red warning lamp illuminated) . The same

condition required by a normal regeneration are to be meet.

Figure 56.

DPF Regen

Summary of Contents for IIDTool Pro G3


























































































































































































Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands

Gap Diagnostic IIDTool Pro G3, User Manual

Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands