background image

GAT ECO.Side Lock 7000 BA / NW BA  
Installation

 

 

www.gantner.com

 

HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14

 

27

 

 

Installation Requirements for the GAT ECO.Side Lock 7000 BA and Metallic Doors 

 

During installation, please pay attention to the following points: 

 

The thickness of the locker door must be between 18 and 26 mm (0.71´´ and 1.02´´). See Figure 3.11. 

When the door is pressed shut, ensure there is no gap between the bolt set (2) and the front of the GAT ECO.Side 
Lock 7000 BA. Ideally the bolt set should touch the front of the lock (see measurement in Figure 3.11). 

-   The locker door, the bolt set, and the front side of the GAT ECO.Side Lock 7000 BA must be perpendicular and 

parallel to each other. If not, the door contact in the GAT ECO.Side Lock 7000 BA can potentially not function 

correctly. 

 

 

 

If right and left-hinged locker doors are in use together, please note the correct LED position. The GAT ECO.Side 
Lock 7000 BA is mounted upside-down on left doors in comparison to right doors. 

 

 

   

   Figure 3.13 - LED positions of the GAT ECO.Side Lock 7000 BA for right and left-hinged doors 

 

NOTE!

  Before installing all locks in a new locker system, a test installation of one lock into a completed locker 

and a function check must be performed. See section “3.3 Test Installation”. 

Summary of Contents for GAT ECO.Side Lock 7000 BA

































































Reviews: