G&D DL-Vision(M/S)-AR Installation And Operation Manual Download Page 47

Page: 47 / 56

Status displays

G&D DL-Vision(M/S) ·

Status displays

The LEDs on the front panel of the computer module and the user module enable

you to control the KVM extender’s operating status at any time.

Meaning of the LEDs on the front panels

Range

LED

Status

Meaning

Ident.

Lights up as soon as the LED has been activated

via the web application.

Power

Red.

The power pack is switched on and supplies the

necessary voltage.

off

The power pack is switched off or the device is not

connected to the power network.

Main

The power pack is switched on and supplies the

necessary voltage.

off

The power pack is switched off or the device is not

connected to the power network.

Status

Ready

blinking

Device is ready for operation.

off

Device is booting or defective internal commu-

nication.

System

blinking

Device is ready for operation

off

Defective internal communication

flickering Device is booting

Summary of Contents for DL-Vision(M/S)-AR

























































Search results

Summary of Contents for DL-Vision(M/S)-AR

Reviews:

Related manuals for DL-Vision(M/S)-AR

Brands by name

Popular brands

G&D DL-Vision(M/S)-AR, Installation And Operation Manual

Search results

Summary of Contents for DL-Vision(M/S)-AR

Reviews:

Related manuals for DL-Vision(M/S)-AR

Brands by name

Popular brands