manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 98

A:96

AK 98 Dialysis Machine - Haemodialysis - Double needle

treatment

HCEN12745 Revision 10.2016

Program version 2.xx

CAUTION!

It is important to set a correct ultrafiltration rate for the patient, to avoid incorrect fluid
removal. Set a minimum ultrafiltration rate according to the instructions for the
specific dialyzer.

CAUTION!

Once treatment parameters are set, you must verify that all calculated treatment
values are as intended.

CAUTION!

Additional measures to supervise the patient weight loss is recommended when
treating low weight patients or when performing long treatments. For Ultrafiltration
details, refer to Technical data and specifications.

Procedure

1)

Press the

Time

indicator.

2)

Press

UF volume

.

3)

Calculate the patient’s ultrafiltration
volume, see Section 4.2.10

“Set

ultrafiltration volume”

on page A:95.

4)

Enter the patient’s ultrafiltration volume.

5)

Press

OK

.

4.2.11

Set heparin values

Before you begin

WARNING!

Make sure to set the prescribed heparin values. Incorrect heparin settings may
cause blood coagulation or internal bleeding.

Procedure

1)

Press the

Blood

button.

2)

Select the

Heparin

tab.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands