manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 96

A:94

AK 98 Dialysis Machine - Haemodialysis - Double needle

treatment

HCEN12745 Revision 10.2016

Program version 2.xx

10)

Only for single needle treatment:

The

expansion chamber is filled to a suitable
level during priming. Close the clamp
above the expansion chamber. See
Section 5

“Haemodialysis - Single needle

treatment”

on page A:105 for more

information.

4.2.8

Priming options

4.2.8.1

Extra priming

When the priming is complete an information message will be displayed, containing a
selection of possible actions.

Procedure

1)

Check that you have enough priming fluid.

2)

Press

Extra priming

.

3)

Press the flashing

Blood pump

button.

4)

CAUTION!

Check carefully that the
venous blood line is correctly
placed in the priming
detector to make sure that
the supervision of alarms is
activated.

When the extra priming is completed:
Press

Connect patient

.

5)

Continue starting the treatment. See
Section 4.2.9

“Set treatment time”

on

page A:95.

4.2.8.2

Recirculation

When the priming is complete an information message will be displayed, containing
the possible actions to recirculate.

You can set the priming fluid to circulate in the blood lines.

Procedure

1)

Press

Recirculation

.

2)

Connect the two patient ends of the blood lines to make a closed circuit. Use a
sterile disposable blood line connector.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands