manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 72

A:70

AK 98 Dialysis Machine - Handling the dialysis machine

HCEN12745 Revision 10.2016

Program version 2.xx

3.5

Concentrate standby mode

3.5.1

About concentrate standby mode

It is possible to put the machine into concentrate standby mode. In standby mode the
consumption of concentrates will be stopped. It is also possible to reduce the water
consumption.

Concentrate standby mode can be activated when functional check is done and the
flow diagram turns green.

When the concentrate standby mode is active, a message will be displayed in the
Information field. The bypass path of the flow diagram will turn to orange.

After 1 hour in concentrate standby mode the dialysis machine will automatically start
the dialysis fluid preparation again.

Concentrate standby mode cannot be activated if blood has been detected.

Concentrate standby mode can be activated manually (default function) or preset to be
activated automatically

. The presets are configured by an authorized service

technician.

Concentrate standby mode cannot be performed at the same time as recirculation.

3.5.2

To manually activate concentrate standby mode

Procedure

1)

Press the

Fluid

button.

2)

Select the

Fluid flow

tab.

3)

Press the activate button to activate
concentrate standby mode.

3.5.3

To resume preparation of dialysis fluid

Procedure

1)

Select the

Information

tab.

2)

Press

Confirm

in the message.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands