manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 66

A:64

AK 98 Dialysis Machine - Handling the dialysis machine

HCEN12745 Revision 10.2016

Program version 2.xx

●

Stroke volume

: Read out of actual stroke volume.

●

Mean blood flow

: Read out of effective blood flow rate during treatment.

Tools

●

Service

: Open the

Service menu

.

●

Clean screen

: Allows the operator to clean the screen when the machine is

switched on. It is possible to perform this procedure in any machine status. When
the command has been activated the screen is temporarily disabled, allowing the
operator to clean it.

●

Night light

: Turns off the operator´s panel. Press the operator´s panel at any

time to reactivate it. Any new alarm reactivates the operator´s panel.

3.4.20

Fluid button (25)

The

Fluid

button opens the

Fluid Menu

, which contain tabs for handling parameters

related to the fluid path.

WARNING!

The maximum UF rate must be preset by an authorised technician according to the
patient’s prescription, when AK 98 dialysis machine is used in home healthcare
environment.

UF rate

●

UF volume

: Set the ultrafiltration volume (patient weight loss).

●

Treatment time

: Adjust the treatment time. Time menu will display total set

treatment time.

●

Set minimum UF rate

: Set the minimum ultrafiltration rate to be applied, as

required during the treatment.

●

Isolated UF

: Set the isolated ultrafiltration values, see Section 6

“Isolated

ultrafiltration”

on page A:113.

●

Profiling

: Set the ultrafiltration profile, see Section 7.1

“General”

on page A:118.

●

Calculated UF rate

: Read out of the calculated ultrafiltration rate.

●

Accumulated UF volume

: Read out of accumulated ultrafiltration volume (patient

weight loss).

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands