manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 293

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Attentions

B:93

518 CleanCart is not attached

518 CleanCart is not attached 

Attach CleanCart cartridge. 

Appears:

When the CleanCart cartridge is not properly attached to
the BiCart cartridge holder during a heat disinfection
program.

Machine actions:

After 1 minute there is a buzzer sound. The delay is only
valid at first occurrence.

Operator action:

1.

Attach the CleanCart cartridge to the BiCart cartridge
holder.

2.

If it is already attached, make sure it is properly located.

See Section 10.3.4

“Start a heat disinfection with a

CLEANCART cartridge”

on page A:146 in Operators

handbook.

Mute time:

Permanent.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands