manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 170

A:168

AK 98 Dialysis Machine - IT Connectivity

HCEN12745 Revision 10.2016

Program version 2.xx

12.3

Cancel prescription retrieval

If

Cancel

is pressed the identified patient and the patient prescription will be discarded

and all set parameters will revert to default.

To retrieve the prescription again repeat the steps in Section 12.2

“Confirmed Patient

ID and retrieval of patient prescription when the Patient ID is confirmed”

on

page A:166.

A prescription can be retrieved until treatment is started or until the prescription is
confirmed.

12.4

Clearing Patient ID and patient prescription

The treatment parameters will revert to default/startup values if the

Clear

button is

pressed before the treatment starts. If the

Clear

button is pressed when the AK 98

dialysis machine is in treatment mode, only the patient's ID will be cleared. Parameter
settings will remain unchanged.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands