manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

Share
Download
Gambro AK 98 Operator'S Manual Download Page 151

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Disinfection and cleaning

A:149

3)

Press

Auto schedule

.

4)

Select day.

5)

Press

Off

.

6)

Press

OK

.

10.3.8

Integrated heat disinfection with a WRO 300 H unit

10.3.8.1

Integrated heat disinfection with a WRO 300 H unit

An integrated heat disinfection program has an extra phase compared to normal heat
disinfection. In this phase hot water from the water purification unit WRO 300 H slowly
flows through the dialysis machine. This means that also the inlet water tube is
disinfected. Therefore, choose integrated heat disinfection if possible. For more
information, see Section 11

“Disinfection with the AK 98 dialysis machine and WRO

system”

on page A:159

10.4

Chemical disinfection

10.4.1

About chemical disinfection

During the chemical disinfection program the machine is filled with a concentrated
disinfectant

. Concentrated disinfectant is mixed with water to the correct

concentration in the machine. The diluted solution fills all parts of the fluid path. After a
certain time (dwell time) the fluid path is rinsed and drained.

Heat disinfection can be replaced by chemical disinfection. But note that decalcification
(CLEANCART C cartridge or liquid citric acid) cannot be replaced by chemical
disinfection.

10.4.2

Start a chemical disinfection

Procedure

1)

Press the

Disinfection

button.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands