manualshive.com logo in svg

Gambro AK 98, Operator'S Manual

The Gambro AK 98 Operator's Manual is available for free download from our website. This comprehensive manual provides essential instructions and guidance for operating the Gambro AK 98. Gain a deeper understanding of this product's features and functionality by accessing the manual at manualshive.com.

Share
Download
background image

A:130

AK 98 Dialysis Machine - Measuring blood pressure

HCEN12745 Revision 10.2016

Program version 2.xx

CAUTION!

If the patient has other monitoring devices on the same arm as the cuff, these
devices may not work as they should while the blood pressure is measured.

CAUTION!

Do not apply a cuff to a limb that has restricted blood flow as this may affect the
blood pressure measuring.

CAUTION!

Do not apply a cuff to a limb with an access, for example a fistula or a graft as this
may have a negative effect of the fistula or graft.

8.3

Direct blood pressure measuring

Procedure

1)

Press the

BPM

readout field.

The measurement starts. The
heart in the read out field starts
flashing and BPM is flashing in the
status bar.

NOTE!

First inflation pressure is 180
mmHg.

Results

The measured value appears in the BPM read out field.

To stop measuring: Press the

BPM

read out field to stop an ongoing measurement.

8.4

Interval blood pressure measuring

Procedure

1)

Press the

BPM

button.

2)

Select the

Setup

tab.

3)

Press

Auto mode

.

4)

Press

Interval time

.

5)

Set how often the blood pressure monitor
should measure blood pressure, a value
between 5 and 60 minutes.

6)

Press

OK

.

7)

Press

Activate

to activate interval blood

pressure measurement.

Summary of Contents for AK 98



































































































































































































































































































































































































Reviews:

No comments

Related manuals for AK 98

zipwake E Series Operator'S Quick Manual preview
E Series
Brand: zipwake Pages: 2
zipwake E Series Start-Up Checklist preview
E Series
Brand: zipwake Pages: 2
ABS ABS-Lock DH04 Series Manual preview
ABS-Lock DH04 Series
Brand: ABS Pages: 4
Bante Instruments ORPscan10 User Manual preview
ORPscan10
Brand: Bante Instruments Pages: 6
Taurus HS 100 Assembly Instructions Manual preview
HS 100
Brand: Taurus Pages: 24
Nederman RBU 1300 User Manual preview
RBU 1300
Brand: Nederman Pages: 255
PASCO ME-9430 Instruction Manual And Experiment Manual preview
ME-9430
Brand: PASCO Pages: 30
Össur i-limb access hand Instructions For Use Manual preview
i-limb access hand
Brand: Össur Pages: 246
Össur PROPRIO FOOT PSX01 Instructions For Use Manual preview
PROPRIO FOOT PSX01
Brand: Össur Pages: 374
Cablexpert NCT-2 User Manual preview
NCT-2
Brand: Cablexpert Pages: 12
MakAlon MK-SM03 User Manual preview
MK-SM03
Brand: MakAlon Pages: 36
SureShot ACFC-10 Operation Manual preview
ACFC-10
Brand: SureShot Pages: 24
Axi STS 6030 Instruction, Operating, & Maintenance Manual preview
STS 6030
Brand: Axi Pages: 27
Quest Leisure Products ELITE Ragley Pro Comfort Instructions Manual preview
ELITE Ragley Pro Comfort
Brand: Quest Leisure Products Pages: 13
KAM DMX1500 Instruction Manual preview
DMX1500
Brand: KAM Pages: 2
Branch Manager T1001 Operation, Maintenance And Spare Parts Manual preview
T1001
Brand: Branch Manager Pages: 28
G-Systems GSE electronic ballast User Manual preview
GSE electronic ballast
Brand: G-Systems Pages: 38
Campbell AeroX Audio 105 Product Manual preview
AeroX Audio 105
Brand: Campbell Pages: 23

Brands by name

Popular brands

Load more brands