Gallagher C300420 Installation Note Download Page 12

Page  12   

3E4290 Gallagher T12 Reader | Edition 1 | August 2016

 

Copyright © Gallagher Group Limited

Approvals and standards

This symbol on the product or its packaging indicates that this product must not be disposed 
of with other waste.  Instead, it is your responsibility to dispose of your waste equipment by 
handing it over to a designated collection point for the recycling of waste electrical and electronic 
equipment.  The separate collection and recycling of your waste equipment at the time of disposal 
will help conserve natural resources and ensure that it is recycled in a manner that protects human 
health and the environment.  For more information about where you can drop off your waste 
equipment for recycling, please contact your local city recycling office or the dealer from whom 
you purchased the product.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.

Note:

  Changes or modifications not expressly approved by Gallagher Limited could void the user's 

authority to operate this equipment.

Note:  

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation.  This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications.  However, there is no 
guarantee that interference will not occur in a particular installation.  If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures:

• 

Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

Industry 

Canada

This device complies with Industry Canada licence-exempt RSS standard(s).  Operation is subject to 
the following two conditions: (1) this device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired operation of the device.

Industrie 

Canada

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio 
exempts de licence.  L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil 
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage 
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

ETSI EN 300 330-2 V1.5.1:2011

 

EN50130-4:2011

 

  

     

    

     

Please refer to the document 

“3E2793 Gallagher Command Centre UL Configuration Requirements”

 for a guide 

to configuring the Gallagher system to the appropriate UL Standard.

US - Equipment: com, burg and acc reader

 

CA - Equipment: com, burg reader

Summary of Contents for C300420














Reviews: