Installation/Operating Instructions
READ THESE INSTRUCTIONS BEFORE FIRING UP YOUR BALLAST
KEEP ORIGINAL PACKAGING
— all returns need to be in the original packaging
in order to avoid product damage during shipping. Any damage to products not in
their original packaging will not be covered under warranty.
SAFETY FIRST!
Failure to observe the following safety warnings may result in
serious injury. In addition, failure to observe these safety warnings will result in a
waiver of all liabilities and will void all warranties.
WARNING
If the exterior of the lamp is damaged, replace lamp immediately.
When re-lamping, make sure lamp has time to cool before touching.
Make sure lamp is correctly locked into the reflector socket, properly
securing the lamp.
Make sure power cord and lamp cord are connected properly.
Disconnect power before re-lamping.
DO NOT
hang by power or lamp cord.
DO NOT
make contact with the interior of the socket while power is on.
DO NOT
operate light systems in wet locations.
DO NOT
plug system into supply voltage other than what is designated on ballast.
DO NOT
attempt to rewire or reconfigure your system, it will void warranty and
could cause serious safety hazards (i.e. power cord, lamp cord, lamp socket or ballast).
Keep away from children.
Galaxy
®
LEC
™
:
906270 - 315 WATT 120V - 240V
906272 - 315 WATT 277V ONLY
This product contains delicate electronic components. This means that if it is placed
near an object that transmits radio signals, it could cause interference. This could
be, for example, mobile telephones, walkie talkies, CB radios, remote controls and
microwaves. If interference occurs, move such objects away from the appliance.
WARRANTY
This unit, when properly used will provide you with years of service.
It is covered under a 3 year warranty. This warranty will be voided if the unit is
misused, abused or altered. Warranty repair or replacement will be at the sole
discretion of the manufacturer. Defective units need to be returned to the place
of purchase with proof of purchase/receipt.
This warranty is expressly in lieu of all other warranties, expressed or implied, including
the warranties of merchantability and fitness for use and of all other obligations or
liabilities on the part of the seller. This warranty shall not apply to this product or
any part thereof which has been damaged by accident, abuse, misuse, modification,
negligence, alteration or misapplication. Manufacturer makes no warranty
whatsoever in respect to accessories or parts not supplied by manufacturer. This
warranty shall apply only to the United States, including Alaska, Hawaii and territories
of the United States and Canada. This warranty does not cover labor materials, travel
time, equipment, etc. to de-install any lighting fixtures or other equipment.
RETURNING UNITS
Please contact your retail store for returns.
Part 15 compliance
This device complies with Part 15 of the FCC Rules.
Advisory statement
This product may cause interference to radio equipment and
should not be installed near maritime safety communications
equipment or other critical navigation or communication
equipment operating between 0.45-30 MHz.
The interference potential
of the device or system
The interference potential of the device or system is the
operating frequency; < 9kHz.
Maintenance of the system
Unplug the unit, wait 30 seconds, and plug the unit back in.
Simple measures that can be taken
by the user to correct interference
Move the unit away from any radio device.
POSSIBLE CAUSES CORRECTIVE MAINTENANCE
LAMP LOOSE
IN SOCKET
Make sure that the lamp is fully inserted into the socket and that is has been
locked in properly.
INCORRECT
VOLTAGE
Make sure you are using the correct input voltage with ballast. If using
incorrect voltage, disconnect the ballast from the power source immediately.
DEFECTIVE
OR IMPROPER
WIRING
Examine wiring to ensure it agrees with wiring diagrams on ballast label.
Check connections to see that they are secure. If wiring a 240V ballast,
DO NOT use a neutral. The correct wiring is two hot wires and a ground.
POOR ELECTRICAL
CONNECTIONS
Check wiring and lamp contact with socket. Make sure the lamp cord is
firmly seated in output receptacle.
INCORRECT LAMP
Verify that you are using a 315 W Ceramic Metal Halide lamp.
LAMP
DAMAGE
Investigate possibility of outer bulb damage.
Look for broken tubes or loose metal parts. Replace lamp.
TROUBLESHOOTING GUIDE
Follow the troubleshooting tips below. If troubleshooting techniques fail, bring
ballast back to your place of purchase to request warranty service.
LEC
™
Electronic Ballast
LIGHT EMITTING CERAMIC
™
