Welcome to Use G-270/G-280
Please read carefully this user’s Manual in order to have a better understanding of all
functions of G-270/G-280 double-way watch talkers.
Principal Characteristics of this Unit
Watch type with adjustable watchband;
This unit can make simultaneous one-to-one
and one-to-more communication;
Channels for you to select;
With effective communicative distance
of 5KM
With automatic noise removal function;
With automatic electricity saving function;
With channel playing function;
With 24-hour system;
With backlighting display;
Using 3XAAA cells; or lithium battery(depends G066A3 or G066)
With automatic protection functions in battery charging.
Liquid Crystal Display Screen
1. Picture Mode (Selective);
2. Transmission indicator (TX): Indicator in the time of sending messages;
3. Receiving indicator (RX): indicator in the time of receiving messages;
4. Select volume (4 levels): Display the current volume setup;
5. Call dispatch (call
): Indicator in
the time of calling;
6. Battery capacity display: Indicator
when battery is insufficient or low;
7.12-hour system time (12:00);/ Channel number
(COO):Display the current channel
Description of Structure
8
、
Talk/Call (multifunction): Keep pressing this key to send voice message, and quickly press it
twice to send calling sound;
9
、
Up key: Regulate volume: Regulate volume (in the default state).
Adjust channels and time in the menu state;
10
、
Down key: Regulate volume: Regulate volume
(in the default state). Adjust channels and time in
the menu state;
11
、
Power/Menu (Keep pressing the On/Off switch): When
you keep pressing the key, it gives a short music sound
to start the menu and enter the setting function;
12
、
MIC: Built-in microphone;
13
、
Speaker: Built-in speaker; and
14
、
Antenna.
Points for Attention
This unit is in compliance with the communication control standards, so the following rules
and regulations must be observed:
1.
While you use the unit, we do not guarantee that secrets will not be disclosed in
communication;
2.
There must not be any harmful interference to be caused when you use this unit. This unit
must accept interference, if any;
3.
Any unauthorized changes in or adjustment of the built-in setup such as changing frequency,
launching power, or extending antennas, etc beyond the specified range are illegal acts, or
even lead to a breach of telecommunication management and control;
4.
Do not use this unit where there is danger, including gas stations, hospitals, airports or any
other gas or electric places without shield protection;
5.
Do not use any detergent or thinner to wipe or clean this unit. Only use dry, alkali-free or
well-distributed soft cloth to clean batteries, etc;
6.
You can have an ideal talking effect. Please put the antenna upward during the
intercommunication of the talker, and keep it 5 centimeters away from your face talking in
your normal voice; and
7.
This talker have inner cell protection functions. If you do not use it for long, please take out
the cells; and you must charge the cells every 6 months.
Battery Installation
3xAAA battery cell for G066A3 and lithium battery for G066 (attached with the unit) is applied to
this talker.
The installation and replacement of cells are described as follows:
1. Press down the fixed button on the side of the battery cover of this unit to open the battery cover;
2. In the time of installing the necessary battery, please place the batteries cell into the cell compartment.
In installation, please note the polarity within the compartment and the cell itself; and
3. Put the cell compartment where it is and lock tightly the fixed button for the cell cover.
! Special Caution: No inserting charger if this unit is not installed
with cell !!!
This talker has an AC charger and can charge the AAA batteries in the following manner:
1. Lift up the earphone /charger jack cover on
the side of this unit;
2. Connect the AC charger to the AC jack of the
outlet;
3. Connect the AC charger to the earphone/charger
jack. In the charging process, the cell volume icon
is shown on the display screen, after battery charging,
such icon will automatically disappear.
Note: If it is the battery charging for the first time,
please charge the cell for as long as solid 12 hours or so.
Battery Volume and Low Battery Operation
When the battery volume is detected as insufficient in the mode of communication and watch, the icon of
battery volume will appear. When the battery volume is detected as insufficient in the communication
mode, and approximately 15 seconds later, the icon will automatically transferred to the watch. At this
time it is necessary to charge the cell on a timely basis. Otherwise, after an hour in the watch mode, the
display screen will be off (with blank display screen). It will stop working, and you should charge the cell
for another 12 hours before you use it again.
Application of Talker
After the cell is installed, it automatically connects power to enter the communication mode;
Press down Power/Menu key for 3 seconds to enter the watch mode, with only time displayed;
In the watch mode, press Power/Menu key for 3 seconds to enter the communication mode;
In the communication mode, press Talk/Call key to launch voice, and open Talk/Call key to receive voice;
In the communication mode, press Power/Menu key for menu selection. Press Up or Down key to set different
values. Exit the Menu mode, and press Talk/Call key or wait for 10 seconds till the unit exits the menu mode to
enter the talk mode. (Note: there is sound of keys for each setup); and
Press Up or Down key (in the default state) to regulate volume to an appropriate level.
Instructions of Menu
This talker has two advanced functions to enter with help of Menu:
1. The communication mode (in the default state)
Menu
→
Channel
→
Time (hour)
→
Time (minute)
→
Call
↓ ↓ ↓ ↓
00 12h am/12h pm 00-59 Two call music sounds
2. The watch mode
Time (hour)
：
Time (minute)
↓ ↓
12h am/12h pm 00-59
(Note: There is time display in both communication and watch mode.)
Channel Setup
In the communication mode, press Power/Menu key for menu selection and the numeric display will
flash on the screen, Press Up key to set up channel C:1. Press Down key to set up Channels C:1; and
Press talk/Call key or wait for 10 seconds until the unit exits the menu mode and enters the talk
mode.
-1-
-2-
-3-
-4-
