background image

 
 
 
 
 

 

• 

“Limited” means that we will repair problems caused by factory defects or 
normal use at no charge. 

 

• 

Before returning a radio to us for warranty service, please call our Service 
Department for a Repair Authorization Number (RAN). This RAN must be 
written below your return address on the outside of the shipping box. Boxes, 
which arrive without a RAN, will be refused, and the shipping company will 
return the unopened box to you. Be sure to have a pen and paper ready along 
with the serial number of your radio before calling. We will give you the RAN 
and our shipping address over the phone. The telephone number of the Service 
Department is (760) 480-8800, and we suggest calling between 10:00 AM and 
4:00 PM Pacific Time. 

 

• 

Please include a note with a detailed description of the symptoms. This is 
important because it will help the technician who works on your radio to locate 
your problem. Intermittent problems are easily overlooked, so be sure to give as 
much detail as possible in your note. Also, please include your telephone number 
in case our technicians have any additional questions. 

 

• 

Do not send your power cord or microphone unless we ask for these items during 
our telephone conversation. 

 

• 

You are responsible for getting the radio safely to us. (We suggest using United 
Parcel Service.) You must pay to ship the radio to us, and we will pay to ship the 
radio back to you. Since we use UPS and they do not ship to Post Offices boxes, 
please provide us with a street address for the return of your radio. 

 

• 

We will repair and return your radio as soon as we can. We appreciate your 
choosing a Galaxy radio and we want you to be on the air as much as possible! 

Be sure to visit our web site at 

 

www.GalaxyRadios.com

 

 
 
 
 

 
 

Printed In Malaysia 

AT3602014R 

PD000822 

 

 
 

 

 

 

DX−55V 

 
 
 

 

 

 
 

 

Full Channel AM/FM Mobile Transceiver 

Built in Frequency Counter with Roger Beep

 

 
 

OWNER’S MANUAL 

WARRANTY 

This radio is covered by a two
year limited parts and labor
warranty

Summary of Contents for DX-55V











Reviews: