background image

37

  Laundry detergents and additives   

en-us

Laundry detergents and additives

Laundry detergents and additives

Adding the correct amount of HE 

detergent

9

WARNING

To avoid risk of poisoning, keep detergents and 
cleaning products out of the reach of children.

Avoid overuse of detergent.

Measure out the detergent according to:

The amount of laundry.

The degree of soiling. 

~

 Page 35

The water hardness. This information can be obtained 
from your local water authority. Soft water requires 
less detergent.

Too much detergent

Excessive foam will reduce washing agitation and 
cause poor washing and rinsing results.

Not environmentally compatible (wastes detergent and 
is not good for the environment).

Too little detergent

Laundry will not be washed clean.

Eventually the laundry will take on a grey and hard 
appearance. Greyish-brown grease spots may stain 
the laundry, heating elements may begin to calcify.

The fabric care label is important for selecting the 
correct detergent, temperature and treatment of the 
laundry.

If desired you can visit the following sites for additional 
information on detergents and fabric care. 

 www.textileaffairs.com or www.cleanright.eu

Standard detergent with optical brighteners

Suitable for white laundry made from linen or cotton

Program: COTTONS / Cold - Extra Hot

Detergent for colors without bleach or optical brighteners

Suitable for colored laundry made from linen or cotton

Program: COTTONS / Cold - Hot

Detergent for colors/delicates without optical 
brighteners

Suitable for colored laundry made from easy-care and 
synthetic fabrics.

Program: EASY CARE / Cold - Hot

Detergent for delicates

Suitable for delicate, fine fabrics, silk or viscose

Program: DELICATES/SILK / Cold - Hot

Detergent for woolens

Suitable for wool

WOOL program: Cold - Warm

Saving energy and reduce detergent

For light and normal soiling, you can save energy (lower 
washing temperature) and detergent.

NOTICE

When measuring the amount of all detergents/additives/
care products and cleaning agents, please always check 
the manufacturer's instructions and information. 

Saving

Soiling/note

Reduced 
temperature 
and detergent 
quantity as 
per the 
recommended 
dosage

Light

 e.g.: 

Light summer/sports clothing 
(worn for a few hours)

T-shirts, shirts, blouses (worn 
for up to one day)

Guest bed linen and hand 
towels (used for one day)

No visible dirt or stains. Clothing 
has taken on some body odor.

Temperature 
as per the 
care label and 
detergent 
quantity as 
per the 
recommended 
dosage for 
heavy soiling

Normal

 e.g.:

T-shirts, shirts, blouses 
(sweat soaked, worn a few 
times)

Towels, bedding (used for up 
to one week)

Visible dirt or a few light stains.

Heavy

Dirt and/or stains clearly visible, 
e.g. tea towels, baby items, work 
clothing

Summary of Contents for WM262700

























































Reviews: