Gaggenau AL 400 791 Installation Instructions Manual Download Page 5

5

9

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING

Before you plug in an electrical cord or turn on power 
supply, make sure all controls are in the OFF position.

For appliances equipped with a cord and plug, do not 
cut or remove the ground prong. It must be plugged into 
a matching grounding type receptacle to avoid electrical 
shock. If there is any doubt as to whether the wall 
receptacle is properly grounded, the customer should 
have it checked by a qualified electrician.

If required by the National Electrical Code (or Canadian 
Electrical Code), this appliance must be installed on a 
separate branch circuit.

WARNING

To reduce the risk of fire or electric shock, do not use 
this fan with any solid-state speed control device.

Installer – show the owner the location of the circuit 
breaker or fuse. Mark it for easy reference.

Before installing, turn power OFF at the service panel. 
Lock service panel to prevent power from being turned 
ON accidentally.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, 
OR INJURY TO PERSONS, OBSERVE THE 
FOLLOWING:

Use this unit only in the manner intended by the 
manufacturer. If you have questions, contact the 
manufacturer.

Before servicing or cleaning unit, switch power off 
at service panel and lock the service disconnecting 
means to prevent power from being switched on 
accidentally.
When the service disconnecting means cannot be 
locked, securely fasten a prominent warning device, 
such as a tag, to the service panel.

Be sure your appliance is properly installed and 
grounded by a qualified technician. Installation, 
electrical connections and grounding must comply with 
all applicable codes.

WARNING

Risk of electric shock

Parts inside the appliance can have sharp edges. The 
connection cable can be damaged. Do not bend or 
pinch connection cables during installation.

Related Equipment Safety

Remove all tape and packaging before using the 
appliance. Destroy the packaging after unpacking the 
appliance. Never allow children to play with packaging 
material. 

The appliance should only be used if installed by a 
qualified technician in accordance with these 
installation instructions. The manufacturer is not 
responsible for any damage resulting from incorrect 
installation.

Never modify or alter the construction of the appliance. 
For example, do not remove leveling legs, panels, wire 
covers or anti-tip brackets/screws. 

Proposition 65

 

Warning:

This product may contain a chemical known to the State 
of California, which can cause cancer or reproductive 
harm. Therefore, the packaging of your product may 
bear the following label as required by California:

&DQFHUDQG5HSURDUP

ZZZ3:DUQLQJVFDJRY

67$7(2)&$/,)251,$352326,7,21:$51,1*

:$51,1*

Summary of Contents for AL 400 791









































Reviews: