Gadspot GS2011VN Page 12 User Manual Download

Page: 12 / 72

H.264 Network Digital Video Recorder User Manual

2.5 Installation connections sketch map

(Below just as the 4CH DVR for example,Specifically please

refer to practical product.)

2.6 Audio and video input and output connections

2.6.1 Video input connections

The video input port is BNC connector plug. The demand of input signal is PAL/NTSC BNC(1.0V

P-P

,75Ω).

The video signal must be accorded with the state standard which has the high signal to noise ratio, low

aberration and low interference. The image must be clear and has natural color in the appropriate brightness.

Insure the camera signal stable and credible

The camera should be installed in the appropriate location where is away from backlighting and low

illumination or adopts the better backlighting and low illumination compensation.

The ground and power supply of the camera and the DVR should be shared and stable.

Insure the transmission line stable and credible

The video transmission line should adopt high quality coaxial pair which is chosen by the transmission

distance. If the transmission distance is too far, it should adopt shielded twisted pair, video compensation

Summary of Contents for GS2011VN









































































Search results

Summary of Contents for GS2011VN

Reviews:

Related manuals for GS2011VN

Brands by name

Popular brands

Gadspot GS2011VN, User Manual

Search results

Summary of Contents for GS2011VN

Reviews:

Related manuals for GS2011VN

Brands by name

Popular brands