2
© 2018 Copyright All Rights Reserved
EEG6500 Enhanced Electronic Governor
05.09.18
PIB 5010
F
WARNING
Loss of Magnetic Pickup Sensing
If EEG detects no input from the magnetic pickup, the EEG
will set the actuator to 0V and set the speed to 0 RPM. The
display will flash the RPM along with the Warning Indicator.
Parameters will be unchangeable.
A
D
C
B
E F
N P
Actuator
Battery
- +
Magnetic
Speed
Pickup
Fuse 15A M
ax
Ground to Case
(12V or 24V)
A
N
D
C
B
E
H
G
F
L
K
J
M
P
A
N
D
C
B
E
H
G
F
L
K
J
M
P
CAN J1939
( Optional )
Accessory
Input
Droop
Idle
Variable Speed / Trim
Potentiometer
120 Ohms
( End of CAN bus)
Ground to
Case
Ground to
Case
5KΩ
COM
VSPD
5
DISPLAY & CONTROLS
4
WIRING
TERM
DEFINITION
GAUGE
AWG / mm
2
NOTES
A
Actuator (+)
#16 / 1.31
B
Actuator (-)
#16 / 1.31
C
Magnetic Pickup (+)
#20 / 0.52
* Twisted wires 14 turns per foot.
0.02in (.51mm) gap between sen-
sor and gear teeth.
D
Magnetic Pickup (-)
#20 / 0.52
E
Battery (-)
#16 / 1.31
F
Battery (+)
#16 / 1.31
A 15 amp fuse must be installed
in the positive battery lead to pro-
tect against any overload or short
circuit
H
Ground Signal
#16 / 1.31
Reference for variable speed/trim
input & switches
J
Variable Speed Input
#20 / 0.52
5K
Ω
Resistive, 0-2.5 VDC or
4-20mA. Increasing Voltage. Resis-
tance or Current Increases Speed
K
Droop Select
#16 / 1.31
Active when connected to Terminal
H
L
Idle Select
#16 / 1.31
Active when connected to Terminal
H
M
Aux Input
#20 / 0.52
Load sharing / synchronizing, 5V
nominal (0-10V), reverse ramp
N
CAN L
#20 / 0.52
Twist wires 14 turns per foot.
P
CAN H
#20 / 0.52
RECOMMENDATIONS
One row of parameters is displayed at a time.
Row 2 Column 3
Parameter
Adjust Up
Parameter
Adjust
Down
Increment a Parameter Value:
HOLD and TAP or
Rapidly Increment a Value:
HOLD and HOLD or
Locking/Unlocking the Display
Press and hold both the UP and DOWN arrows simultane-
ously for 3 seconds to UNLOCK or to LOCK the display.
“Over Speed” will blink when the unit is in overspeed.
(Cycle power to restart)
Once the LOCK parameter on the main menu is enabled
(”ON”), the display can be manually unlocked.
If the EEG detects an actuator overcurrent it will
terminate power to the actuator, the display will
flash Actuator Current along with the warning
indicator. (Cycle power to restart)
Displays the units for the parameter (e.g. RPM)
Parameter Units
Displays the value of a selected parameter or live
running parameter. This
area will blink if a system
shutdown and restart is
required.
Parameter Value
Pressing either the UP or DOWN arrow allows you to tog-
gle through the five secondary parameters: Engine Speed
(RPM), Duty Cycle (%), Actuator Current (Amps), Engine
Speed (Hz) and Variable Speed (%)
Tap
or
Secondary Parameters
Overcurrent
B
A
C
Tap any
For: SPEED
For: IDLE
For: FUEL LIM
Hold
To change the displayed row of parameters:
To view a parameter value in a selected row:
Hold: Button A
Hold: Button B
Hold: Button C
Column Select Buttons
Parameter Adjust
Quikset Menu
5K Ohm Resistive Speed Trim Pot.:
0-2.5 Volt or 4-20mA* Variable Speed Input:
Fuel Limit
If the EEG detects that the FUEL LIMIT setting
has been exceeded, the display will flash the
FUEL LIMIT along with the warning indicator.
Paramters will be unchanged.
Over Speed
Lock Feature
* 4-20mA input requires an external 200 Ohm
resistor across Terminals H & J
IMPORTANT:
When installing, be sure there’s a good connection between
the case of the EEG6500 and chassis / battery ground.