background image

Precautions

1 、 Select a correct location to place the unit
2 、 Do not move or operate unit where it could tip
3 、 Use cart or unit handle to move unit 
4 、 Charging produces explosive gases,Never smoke or allow a spark or
   flame in vicinity of battery or engine.

5 、 Operate charger indoor with good ventilation .Do not operate cha-
   rger to rain or snow or use when wet.

6 、 Disconnect input power before using charging clips.
7 、 Electricity arc and spark exist in some electrical component parts 
   of charger such as power switch and relay during normal charging
   batteries. Keep charger away from inflammables and explosives

8 、 Do not stop charging suddenly before battery fully charged.Also,
   never allow clips touch each other.

9 、 Do not operate charger with damaged cord or plug—replace the cord
   or plug immediately 

10 、 Never charge a frozen battery.
11 、 Use only qualified fuse.
12 、 Clean the battery which will be charged before charging. And 
    check the initial voltage of the battery.

13 、 Never set Mode switch to “0”position for charging batteries.
14 、 Do not charge damaged battery ,otherwise it will damage the bui-
    ld-in protection

15 、 Do not switch charging current while battery is being charged.

Page.4

Summary of Contents for GI35114














Reviews: