FDLS-1
Dual RX Link system
How to Use
How to Use
LED Indication
LED Indication
Precautions
Precautions
1.
Install two receivers on the aircraft as shown
in the wiring diagram on the next page.
2.
Link the two receivers using the dual receiver
feature of the transmitter.
For systems without dual receiver capability,
link each receiver in turn.
WARNING
Failure to follow these safety precautions may
result in severe injury to yourself and others.
In order to prevent any short circuits,
please observe the polarity of all
connections.
Ensure that the unit is connected
properly to the receiver.
■
If the connector is disconnected during
flight, it becomes inoperable.
Ensure that the unit is mounted in an
area that will eliminate exposure to
fuel, water and vibration.
■
As with any electronic components, prop-
er precautions are urged to prolong the life
and increase the performance of the unit.
Allow a slight amount of slack in the
unit cables and fasten them at a
suitable location to prevent any damage
from vibration during flight.
Be sure to link the two receivers with
the transmitter.
■
It will not work unless the two receivers
are linked. After startup, even if the link on
one side is disconnected, the other side will
continue to operate normally.
Used in a set of Futaba S.BUS / S.BUS2
systems.
Do not supply receiver power from
the ESC. When using the receiver
power supply type ESC, remove the red
(+) cord of the 3ch wiring from the ESC
so that the power is not supplied from
the ESC.
■
Use a dedicated battery to power the
receiver / servo.
Don't mount FDLS-1 away from
magnetic bodies.
To ensure that the FDLS-1 is
functioning as desired, please test
accordingly.
■
Do not fly until inspection is complete.
Before the flight, disconnect the
wiring of the main receiver from
the FDLS-1 that is operating normally,
and check if the sub receiver alone can
control it.
■
Check if the FDLS-1 switches.
Do not use the FDLS-1 with
anything other than an R/C model.
1M23N37402
LED
Transmitter in link mode
Transmitter in link mode
For FASSTest 18CH Select
dual mode and link primary
*Follow the link procedure
for each receiver manual.
For FASSTest 18CH Select dual
mode and link secondary
Turn on the main
receiver and link
Turn on the sub
receiver and link
Main RX
Sub RX
Works with the
main receiver
Trouble occurred in the
main receiver ！！
FDLS-1 automatically
switches to sub-receiver
Switch to the main receiver
when communication is
recovered
Appllcable systems
S.BUS/S.BUS2 receiver
*Except for cars
Install two receivers
in one fuselage.
FDLS-1
is a secure system. In the event of
trouble with the main receiver, the
FDLS-1
will automatically switch to the sub receiver
and fly safely.
Thank you for purchasing the FDLS-1. Before us-
ing your new FDLD-1, please read this manual thor-
oughly and use the FDLD-1 properly and safely.
After reading this manual, store it in a safe place.
Instruction Manual
Use :
Two receivers communication
switching device
Length :
225 mm (8.9")
Weight :
6.5 g (0.2 oz)
Operating voltage :
DC3.7 V to 7.4 V
(Acceptable: DC3.5 V to 8.4 V)
Green 1 blink
Main Rx operation
Green 2 blinks
Sub Rx operation
Red
No signal reception
Green/Red
Alternate blink Unrecoverable error
◆ About telemetry system
When using the dual receiver function
・The telemetry function of the main receiver
can be used
・Sub-receiver telemetry function is not available
Other than dual receiver function
・Telemetry not available
・Set telemetry to INH (disabled)
