background image

Thank you for purchasing a Futaba 2PC / 2PCKA.

Before using your 2PC / 2PCKA, read this manual carefully and

use your R/C set safely.

After reading this manual, store it in a safe place.

-No part of this manual may be reproduced in any form without prior permission.
-The contents of this manual are subject to change without prior notice.
-This manual has been carefully written. Please write to Futaba if you feel that any corrections or clarifications

should be made.

-Futaba is not responsible for the use of this product.
-Futaba is registered trademarks of FUTABA Corporation.

THE FOLLOWING STATEMENT APPLIES TO THE RECEIVER (FOR U.S.A.)

This device complies with part 15 of the FCC rules. Operation is subject to the fol-
lowing two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.

APPLICATION, EXPORT, AND RECONSTRUCTION

2. Exportation precautions
(a) When this product is exported from Japan, its use is to be approved by the Radio
Law of the country of destination.
(b) Use of this product with other than models may be restricted by Export and Trade
Control Regulations. An application for export approval must be submitted.

3. Modification, adjustment, and replacement of parts
Futaba is not responsible for unauthorized modification, adjustment, and replace-
ment of parts of this product.

1. Use this product in models only.
The product described in this manual is subject to regulations of the Ministry of Ra-
dio/Telecommunications and is restricted under Japanese law to such purposes.

Summary of Contents for 2PC



















Reviews: