manualshive.com logo in svg

Furuno FCV-38, Manual

Share
Download
Furuno FCV-38 Manual Download Page 99

4.  ADVANCED SETTINGS

4-17

4

4.7.4

User Interface Settings menu

You can change the language, units used for measurement, screenshot settings, etc.

* Whenever a unit of measurement is changed, the message shown below appears. 
If you are sure to proceed, click the [Yes] button.

Menu item

Description

[Language]

Selects the language to display the menus and on-screen in-
dications in.

[Depth]*

Selects the unit of measurement for depth.

[Speed]

Selects the unit of measurement for speed.

[Temperature]*

Selects the unit of measurement for temperature.

[Fish Size]*

Selects the unit of measurement for fish size.

[Save Destination For Screenshots] Selects the save destination for screenshots. See 

section 3.1.1.

[Save Intervals For Screenshots]

Selects the interval timing for taking repeated screenshots. 
section 3.1.3.

[Echo Data Recording Method]

Selects the data format to use to record echo data. For de-
tails see section 3.2.1.

FCV-38[ver 0252473-xx.xx]

Summary of Contents for FCV-38

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands