manualshive.com logo in svg

Furuno FCV-38, Manual

Share
Download
Furuno FCV-38 Manual Download Page 48

1.  OPERATION

1-36

1.22

How to Set, Show and Hide Alarms

The FCV-38 has five alarms, Bottom Alarm, Fish Alarm, Bottom Fish Alarm, Tempera-
ture Alarm, and Fish Size Alarm.

When an alarm is set and the conditions meet the alarm requirements, the system re-
leases an audible beep and the applicable alarm icon appears at the bottom-right cor-
ner. 

To silence the audible beep, click anywhere on the screen. The alarm icon remains 
visible on the display until the cause of the alarm is removed.

Alarm descriptions

• 

Bottom Alarm

: Alerts you when the seabed (bottom) enters the range set for this 

alarm.

• 

Fish Alarm

: Alerts you when fish are detected within the range set for this alarm.

• 

Bottom Fish Alarm

: Alerts you when fish are detected within the range set for this 

alarm.

• 

Temperature Alarm

: Alerts you when the water temperature is within range or out 

of range, depending on your selection. This alarm requires water temperature data.

• 

Fish Size Alarm

: Alerts you when a fish on the selected fish size bar When the se-

lected fish size graph bar is 1st peak, and a fish is detected that meets or exceeds 
the size and/or distribution of 1st peak on the fish size graph bar. The fish size graph 
must be active to use this alarm.

: Bottom Alarm icon

: Bottom Fish Alarm icon

: Fish Size Alarm icon

: Temperature Alarm icon

: Fish Alarm icon

Summary of Contents for FCV-38

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands