background image

1

1.

MOUNTING

1.1

IP Handset

The IP Handset functions as a display and it may also be used for normal voice com-
munication. A maximum of 16 units can be installed anywhere onboard the vessel. 
The IP Handset is provided with a cradle assembly (chassis cradle and cradle). The 
assembly is designed for both bulkhead and desktop installations, with cable entries 
for both methods.

1. To use the rear cable entry, make a hole of 18 mm (0.71") diameter in the instal-

lation site. See the outline drawing at the rear of this manual for details.

2. Install the chassis cradle with three self-tapping screws (3

20).

3. Connect the curled cord from the IP Handset to the RJ-45 port indicated in the 

above figure.

Note: 

To avoid possible faults in the IP Handset, do not plug or unplug the hand-

set while the Communication Unit or PoE hub (local supply) are turned on.

4. Secure the curled cord with a cable tie (supplied).

Do not apply paint, anti-corrosive sealant or contact 
spray to coating or plastic parts of the equipment.

Those items contain organic solvents that can damage 
coating and plastic parts, especially plastic connectors.

NOTICE

: Screw holes, 

3 places × ø4.6

Chassis 
cradle

RJ-45 port for 
IP Handset

RJ-45 port for 
Communication 
Unit

Cable tie

Curled cord from IP Handset

Summary of Contents for FB-8001













Reviews: