manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 3

i

 

SAFETY INSTRUCTIONS

CAUTION

CAUTION

WARNING

Careful consideration is required to avoid 
ingress of water through the transducer tank. 
The tank shall be strong enough to withstand 
the water pressure in fully loaded conditions in 
rough weathers. FURUNO Electric Co., Ltd. is 
not liable to any loss of ship and personnel 
which is caused by installation procedures.

The installer must read the applicable safety instructions before attempting to operate or install the 
equipment.

Indicates a potentially hazardous situation which, if not avoided, 
could result in death or serious injury. 

WARNING

Indicates a potentially hazardous situation which, if not avoided, 
can result in minor or moderate injury.

CAUTION

Warning, Caution

Prohibitive Action

 Mandatory Action

Ground the equipment to prevent 
electrical shock and mutual 
interference.

Observe the following safe compass 

distances to prevent interference to a 

magnetic compass:

Standard 
compass

Steering 

compass

0.50 m

0.35 m

Display Unit (DS-8500)

2.30 m

1.45 m

Distributor Unit (DS-8510)

1.95 m

1.25 m

2.00 m

1.15 m

Transceiver Unit (DS-8520)

Junction Box (CI-630)

Be sure to power each unit with 
proper voltage.

Connection of an improper power supply 
can cause fire or damage the equipment.

Do not open the equipment.

This equipment uses high voltage 
electricity which can shock, burn or 
cause serious injury. Only qualified 
personnel can work inside the equipment.

Turn off the power at the mains 
switchboard before beginning the 
installation.

Fire, electrical shock or serious injury can 
result if the power is left on or is applied 
while the equipment is being installed.

Do not install the equipment where it 
may get wet from rain or water splash.

Water can cause fire or electrical shock, 
or damage the equipment.

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands