Furuno DRS6A-NXT, Installation Manual

Page: 15 / 40

1. INSTALLATION AND WIRING
8
7. Apply marine sealant to the holes and bolts at the locations indicated with arrows
in the figure below. Also apply marine sealant to the junction between the radiator
and the radiator bracket.
1.5 Mounting the Antenna Unit
The antenna unit can be mounted using the fixing holes on the outside (200

200 mm)
or inside (140

150 mm) the antenna unit. Normally, use the outside fixing holes.
When 140

150 mm fixing holes already exist on the mounting platform, use the in-
side fixing holes.
1. Set the supplied mounting template to the mounting location, then drill four fixing
holes in the mounting location.
Note: The holes must be parallel with the fore and aft line.
2. Attach four corrosion-proof rubber pads (supplied) to the mounting holes.
Apply marine
sealant to these
bolts and holes
Radiator
Bolt assembly - side view (detailed)
Apply marine sealant
to the junction
between the radiator
and radiator bracket. Apply marine sealant
to the junction
between the radiator
and radiator bracket.
Flat washer
Spring
washer
Hex. bolt
Marine sealant
Radiator - bottom view
CAB
LE
ENT
RAN
CE AT
SCANNER F
OR DRS4A/6A/12A/25A
䝇䜻
䝱䝘
ഃ
䜿䞊䝤䝹
ᑟධཱྀ䠄㻰
㻾㻿
㻠㻭㻛
㻢㻭㻛
㻝㻞
㻭㻛
㻞㻡
㻭䛾
䜏䠅
PP
'')
PP
'')
s
PP
'')
PP
'')
s
PP
'')
CENT
ER OF
ANT
ENNA RO
TAT
ION
䜰䞁䝔
䝘ᅇ
㌿
୰ᚰ
PP
'')
ྲྀ ௜✰
4- 䃥
15
FIX
IN
G HO
LES
ྲྀ
௜✰䚷
㻔
᥮
⿦
⏝㻕
4-
䃥 15
(#
: 4
p
lac
es)
FIXING
HOLES
( F
OR RET
ROF
IT
TING)
Not
e:
T
his
tem
plat
e m
ay ha
ve
expand
ed
or
sh
run
k sl
ig
ht
ly.
Ple
ase
conf
irm
di
men
sion
s be
fore
use
.
ὀ
ព
㻦㻌㻌ᮏᆺ
⣬䛿
ಖᏑ≧ែ
䛻䜘
䜚ⱝᖸఙ⦰
䛩 䜛ሙྜ䛜
䛒䜚䜎䛩䚹
㻌㻌㻌㻌㻌㻌
㻌㻌㻌౑
⏝䛾㝿
䛻䛿
ᑍἲ
䜢☜
ㄆ
䛧䛶
䛟䛰
䛥䛔
䚹㻌
BOW
⯪㤳᪉ྥ
DR
S
シリーズ レーダーセンサー（オープン型
）
ᆺ⣬
DR
S S
ERIE
S OPE
N RADA
R SENS
OR
MOUN
TI
NG TE
MPLATE
Bow Bow
Mounting template
Corrosion-proof rubber pad