background image

Safety Warnings for Bunk Beds

1.

Read and follow the information on the WARNINGS shown on the end 
structure of the upper bunk and on the carton. 

2.

Do not remove warning label from the bed.

3.

Keep these instructions for future reference.

4.

IMPORTANT: Must use Bunkie mattress or Bunkie board. The proper 

5.

Surface of mattress must be at least 5 inches (127 mm) BELOW the upper 
edge of guardrails.

6.

The MAXIMUM 

7.

Do not allow children under 6 years of age to use the upper bunk. 

8.

Periodically check and ensure that the guardrails, ladder, handle and other 
components are in their proper position, free from damage, and that all 
connectors are tightened and secured. 

9.

DO NOT allow horseplay, rough playing or jumping on the beds and do not 
allow playing or hiding under the beds. 

10.

Always use the ladder for entering or leaving the upper bunk.

11.

Do not use substitute parts. Contact the manufacturer or dealer for 
replacement parts.

12.

Use of a nightlight may provide added safety precaution for a person using 
the upper bunk. 

13.

Always use the guardrails on both sides of the upper bunk.

14.

If the bunk bed will be placed next to a wall, the guardrail that runs the full 
length of the bed should be placed against the wall to prevent entrapment 
between the bed and the wall. 

15.

The use of water or sleep flotation mattresses is prohibited. 

16.

No more than one person is allowed on the upper bunk at all times.

WARNING:

STRANGULATION HAZARD

Never attach or hang objects to any part of the bunk bed 
that are not designed for use with the bed. Objects such as 
hanger, hook, belt, bag, rope, string, etc. should not be used 
on or around the bunk bed. 

sizes for the UPPER/LOWER TWIN-SIZE Bunkie mattress or Bunkie board
 should be 75” long and 38½” wide with no more than 6” thickness and for 
the UPPER/LOWER FULL-SIZE should be 75” long and 54” wide with no 
more than 6” thickness.

weight capacity for the upper bunk is not to exceed 175 lbs.

Page 1

1

 of 1

1

Summary of Contents for CM-BK922T












Reviews: