background image

Page 13 of 13

Safety Warnings for Bunk Beds

1.

Read and follow the information on the WARNINGS shown on the end 
structure of the upper bunk and on the carton.  Do not remove warning label 
from the bed. Keep these instructions for future reference.

2.

Always use the recommended size mattress or mattress support, or both, to 
help prevent the likelihood of entrapment or falls. The proper mattress sizes 
for the 

UPPER TWIN-SIZE bunk

should be 74” to 75” long x 37½” to 38½” 

wide x 6” high (no higher than 6”) and for the 

LOWER TWIN-SIZE bunk 

should be 74” to 75” long x 37½” to 38½” wide x 6” to 8” high.

3.

Surface of mattress must be at least 5 inches (127 mm) 

BELOW

the upper 

edge of guardrails.

4.

Do not allow persons under 6 years of age to use the upper bunk. 

5.

Periodically check and ensure that the guardrails, ladder, handle and other 
components are in their proper position, free from damage, and that all 
connectors are tighten and secured. 

6.

For safety reasons, especially on the upper bunk bed, 

DO NOT 

allow rough 

playing or jumping on the bed and do not allow playing or hiding under the 
bed. 

7.

Always use the ladder for entering and leaving the upper bunk.

8.

Do not use substitute parts.  Contact the manufacturer or dealer for 
replacement parts.

9.

Use of a nightlight may provide added safety precaution for a person using 
the upper bunk. 

10.

Always use the guardrails on both long sides of the upper bunk.  If the bunk 
bed will be placed next to the wall, the guardrail that runs the full length of 
the bed should be placed against the wall to prevent entrapment between 
the bed and the wall. 

11.

The use of water or sleep flotation mattresses is prohibited. 

12.

No more than one person is allowed on the upper bunk at all times.

13.

The 

MAXIMUM 

weight capacity for the upper bunk is not to exceed 150 lbs.

WARNING:

STRANGULATION HAZARD

Never attach or hang objects to any part of the bunk bed 
that are not designed for use with the bed.  Objects such as 
hanger, hook, belt, bag, rope, string, etc. should not be used 
on or around the bunk bed. 

Summary of Contents for CM-BK1042














Reviews: