
9-11
Chapter 9 Data Review
Recall
1
The selected location will be displayed with blue frame and
will be displayed at the side.
2
To change the location, directly press the desired location or drag the
key up or down.
3
To change the displayed page, press the
/
keys on the left.
NOTE
The apnea duration of 5 seconds or more will be stored. If less than 5 seconds, it will be
stored as "0 (zero)".
Recall
This section explains about the recall function and the setup procedure.
CAUTION
When "Check extended memory" is displayed for the system status message, internal
memory error can be considered.
In such case, full disclosure waveform cannot be properly stored or displayed.
Refer to the "Troubleshooting" section.
The recall data is periodically stored to the internal memory, but if the power has been turned
OFF for 5 minutes or more, maximum of 1 minute of data may be lost. In such case, the lost
data will be displayed as not measured data.
Displayed Items
Press the [Menu], [Recall] ("Data Review") keys.
When the alarm for the specified recall factor occurs, the specified waveform (12 seconds) and numeric data for each
recall factor will be stored up to 1000 data when 1 recall waveform and up to 500 data when 2 recall waveforms. The
recall data to be displayed can be selected. Maximum of 18 compressed recall waveforms will be displayed.
Pressing the waveform area will display the enlarged waveform.
The recall waveform will be acquired from the point prior to alarm occurrence so that alarm-generated point will be
displayed at 7 to 8 seconds point on the 12-seconds recall waveform.
If the recall data exceeds the maximum quantity (1000/500), the data will be erased from the oldest one.
Parameters for each Category
H Module
HR, VPC,VPC-HOUR, ST, SpO
2
, PR_SpO
2
, SpO
2
-2, PR_SpO
2
-2, NIBP, BP1 to 8,
PR-IBP, PDP, PCWP, CPP, T1 to 8, Tb, EtCO
2
, InspCO
2
, RR-GAS, RR-IMP, RR-VENT, APNEA,
O
2
, N
2
O, Agent, E-TV, I-TV, E-MV, P-PEAK, PEEP, P-MEAN, PI, PVI, SpCO, SpMet, SpHb
Vigilance
SvO
2
, ScvO
2
, B-Temp, CCO, CCI
Ventilator
E-TV, I-TV, MV, P-PEAK, PEEP, P-MEAN
Other
BIS, SQI, EMG, SR, Lt-rSO
2
, Rt-rSO
2
, S1-rSO
2
, S2-rSO
2
Summary of Contents for DYASCOPE 8000 Series
